Relación entre las propiedades mecánicas y tribológicas de Ti6AL4V ELI nitrurado mediante descarga intensa de plasma
Resumen
En este trabajo se estudió el comportamiento tribológico, la rigidez y dureza, de la superficie de la aleación Ti6Al4V ELI después de llevar a cabo un tratamiento de nitruración por descarga intensa de plasma a temperaturas de 450, 480 y 520 °C. El par tribológico empleado fue metal-metal (pin de Ti6Al4V ELI - disco de Ti6Al4V ELI con tratamiento) para el respectivo cálculo del coeficiente de fricción. Los ensayos de nanoindentación se realizaron con una punta de ultra alta dureza de módulo de rigidez conocido, que permitió obtener la dureza promedio y el módulo de Young en GPa, de acuerdo con las normas ISO 14577 y ASTM G99-95 respectivamente. Para la caracterización del sustrato, se empleó microscopia electrónica de barrido, microscopia de fuerza atómica y difracción de rayos X, obteniendo así características importantes del comportamiento elástico-plástico, antes y después de aplicarse la nitruración a la aleación por descarga intensa de plasmaDescargas
Lenguajes:
esReferencias bibliográficas
Cunningham, B.W., Hu, N., Zorn, C.M. & McAfee, P.C. (2009). Bioactive titanium calcium phosphate coating for disc arthroplasty: analysis of 58 vertebral end plates after 6- to 12-month implantation. The Spine Journal, 9, pp.836–845. http://dx.doi.org/10.1016/j.spinee.2009.04.015
Fraczek, T., Olejnik, M., Jasi-ski, J. & Skuza, Z. (2011). Short-term low temperature glow discharge nitriding of 316l austenitic steel. METABK, 50(3), pp.151-154.
Kashaev, N., Stock, H.-R. & Mayr, P. (2004). Nitriding of ti – 6% al – 4% v alloy in the plasma of an intensified glow discharge. Metal Science and Heat Treatment, 46(7–8), pp.294-298. http://dx.doi.org/10.1023/B:MSAT.0000048837.39784.e2
Sun, Y. & Bell, T. (1997). A numerical model of plasma nitriding of low alloy steel. Materials Science and Engineering, 224(1-2), pp.33-47. http://dx.doi.org/10.1016/S0921-5093(96)10561-X
Lachtin, J., Krymskij, J. & Sernionov, P.A. (1964). Metalloviedienie i termiceskaja obrabotka metallov. Moscú, Rusia.
Robertson, J. (1993). Deposition mechanisms for promoting sp3 bonding in diamond-like carbon. Diamond and Related Materials, 2(5-7), pp.984-989. http://dx.doi.org/10.1016/0925-9635(93)90262-Z
Meletis, E.I. (2002) Intensified plasma-assisted processing: science and engineering. Surface and Coating Technology, 149, pp.95–113. http://dx.doi.org/10.1016/S0257-8972(01)01441-4
Andrade, M.J. (2007). Comportamiento electroquímico de aleación de Ti6Al4V anodizada en solución de NaH2PO4.2H2O. Scientia et Technica A-o XIII, 36, pp.215-220.
Oliver, W.C., Pharr, G.M. (1992). "An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments," J. Mater. Res., 7, pp.1564-1583. http://dx.doi.org/10.1557/JMR.1992.1564
Hertz, H. (1982). On the contact of rigid elastic solids and on hardness. Verhandlungen des Vereins zur Beförderung des Gewerbefleisses. Leipzig, pp.90-156.
Sneddon, I.N. (1882). The relation between load and penetration in axisymmetric business problem for a punch of arbitrary profile. International Journal of Engineering Science, 3, pp.47-57. http://dx.doi.org/10.1016/0020-7225(65)90019-4
Askeland, D.R. (1998). Ciencia e ingeniería de los Materiales. 3ª Edición. International Thomsom Editores, pp.92-97,107-109.
ASM Comitte of Metallography of titanium and titanium alloys. (1980). Microestructure of titanium and titanium alloys. Handbook eighth edition, American Society of Metals, no 7, pp.312-344.
Tang, J.G., Liu, D.X., Tang, C.B. & Zhang, X.H. (2013). Surface modification of Ti-6Al-4V alloy by cathode assisting discharge setup and conventional plasma nitriding methods. Science China, 56(8), pp.1858–1864. http://dx.doi.org/10.1007/s11431-013-5252-z
Khalaf, M.K., Chiad, B.T., Al-Zubaydi T.L. & Alani, Z.T. (2011). Surface Modification of Ti6Al4V Alloy by Glow Dicharge-Plasma Nitriding. Iraqi Journal of Physics, 9(16), pp. 34-40.
Brading, H.J. (1992). Plasma nitriding with Nitrogen, Hydrogen, and Argon Gas Mixture. Surface Engineering, 8(3), p.207. http://dx.doi.org/10.1179/sur.1992.8.3.206
da Silva, S.L.R., Kerber, L.O., Amaral, L. & dos Santos, C.A. (1999). X-ray diffraction measurements of plasma-nitrided Ti–6Al–4V. Surface and Coatings Technology, 116–119, pp.342-346. http://dx.doi.org/10.1016/S0257-8972(99)00204-2
Meza, J.M., Chaves, C.A. & Vélez, J.M. (2006). Técnicas de indentación: medición de propiedades mecánicas en cerámicas. DYNA, Journal of the Facultad de Minas, Universidad Nacional de Colombia – Medellín Campus, 73(149).
Tang, C.Y., Tsui, C.P., Janackovic, D.J. & Uskokovic, P.S. (2006). Nanomechanical properties evaluation of bioactive glass coatings on titanium alloy substrate. Journal of Optoelectronics and Advanced Materials, 8(3), pp.1194 - 1199
King, E., Fernández González, B.J., de Damborenea González, J.J. & Ruiz Fernández, J. (2000). Nitruración gaseosa a elevada temperatura de la aleación TÍ6AI4V para mejorar su resistencia al desgaste. Revista de Metalurgia, 36, pp.403-409. http://dx.doi.org/10.3989/revmetalm.2000.v36.i6.591
Bemporad, E., Sebastiani, M., Staia, M.H. & Puchi Cabrera, E. (2008). Tribological studies on PVD/HVOF duplex coatings on Ti6Al4V substrate. Surface & Coatings Technology, 203, pp.566–571. http://dx.doi.org/10.1016/j.surfcoat.2008.06.055
Ceschini, L., Lanzoni, E., Martini, C., Prandstraller, D. & Sambogna, G. (2008). Comparison of dry sliding friction and wear of Ti6Al4V alloy treated by plasma electrolytic oxidation and PVD coating. WEAR, 264(1-2), pp.86-95. http://dx.doi.org/10.1016/j.wear.2007.01.045
Barbieri, F.C., Otani, C., Lepienski, C.M., Urruchi, W.I., Maciel, H.S. & Petraconi, G. (2002). Nanoindentation study of Ti6Al4V alloy nitrided by low intensity plasma jet process. Vacum, 67, pp.457-461. http://dx.doi.org/10.1016/S0042-207X(02)00231-2